CP-SX1350 MANUAL PDF

Quick Links. Download this manual. User's Manual - Operating Guide. Thank you for purchasing this projector.

Author:	Mera Mir
Country:	Maldives
Language:	English (Spanish)
Genre:	Health and Food
Published (Last):	8 October 2014
Pages:	145
PDF File Size:	4.20 Mb
ePub File Size:	16.37 Mb
ISBN:	202-2-79596-997-3
Downloads:	21987
Price:	Free* [*Free Regsitration Required]
Uploader:	Dinris

Quick Links. Download this manual. Table of Contents. Moreover, do not. Forward all inquiries. Be sure to read this manual before servicing. The lamp becomes too hot. Never drop it or give it a shock. They may. This projector is provided with a high voltage circuit for the lamp. Do not touch the electric parts of. Do not touch the exhaust fan, during operation.

The LCD module assembly is likely to be damaged. Features 2. Names of each part Adjustment 5. Troubleshooting Service points Wiring diagram Disassembly diagram Replacement parts list RSC commands Block diagram Connector connection diagram Basic circuit diagram Be sure to read cautionary items described in the manual to maintain safety before servicing. Features Ultra high brightness Partial magnification function Whisper mode equipped Keystone distortion correction User memory function Optical lens shift 2.

Adjustment Before adjusting Selection of adjustment When any parts in the table are changed, choose the proper adjusting items with the chart. Make this adjustment after completing the adjustment in E-POS adjustment. Perform these adjustments after the white 6.

To temporarily turn correction off, place the cursor balance adjustment described in Section Make a color uniformity adjustment for the the [ ] key. Similarly, measure adjustment points [No. Select adjustment point [No. First adjust [MIN] tone [G:]. Select [No. Adjustment technique: If the background is [G] monochrome, press the First, adjust [B:] of the point whose color is to [ENTER] key on the Remote control transmitter be adjusted so that it approximates that of to change to solid white.

Before this adjustment, clean the air filter and make sure the projector is compretely assembled. And check standby mode? TSW short or open? PWB assembly Is it repaired? Check at operating mode Does the Lamp Is the computer Make sure Network on lower right corner of the connected with the hardware Network connector light projector directly?

Change to cross-cable, Is the computer or use the straight and projector connected with Please read these instructions before attempting any soldering work. The lamp can break with a loud bang, or burn out, if jolted or scratched, handled while hot, or worn over time.

Note that each lamp has a different lifetime, and some may burst or burn out soon after you start using them. Lamp cover Lamp cover 1. Turn off the projector, and unplug the power cord. Allow the lamp knob bulb to cool for at least 45 minutes, and prepare a new lamp. Slide the lamp cover lock to unlock the lamp 5. Mount the replacement lens. Do not touch about the lens and ventilation openings during use or imme- diately after use prevent a burn. In case that projected image has dark tone around its peripheral, AUTO operation sometimes makes artifacts in the image, shifts capture area and so on.

Those failures are caused by period of image data is not exactly distinguished to period of blanking on signal processing. When any such message is displayed on the screen, please respond as described below. Message Description Lamp usage time is approaching hours. Please pay attention not to remain fiber or fragment of cloth inside the duct.

Wiring diagram Disassembly diagram M : Meter screw T : Tapping screw When removing, lift carefully without excessive force to prevent damaging cables and connectors. Keypad board E, E When removing the Drive board, there might be damage to the flexible cables of LCD panels and two board- to-board connectors. Don't degrade the safety of the projector through improper servicing.

RSC communication Connecting the cable 1 Turn off the projector and the computer power supplies. Use the cable that fulfills the specification shown in the following figure. Block diagram Connector connection diagram Connector connection diagram Basic circuit diagram Parts with hatching are not mounted. CIN S. C SEP. Print page 1 Print document 78 pages. Cancel Delete. Sign In OR. Don't have an account? Sign up! Restore password. Upload from disk. Upload from URL.